User Menus — Instructions

QIACHIP TX118SA transmitter module Instructions manual | wireless 433.92mhz rf module | 1527 learning code | superheterodyne receiver wireless decoding

Instructions Latched Latching Momentary RF Toggle User manual

QIACHIP TX118SA transmitter module Instructions manual | wireless 433.92mhz rf module | 1527 learning code | superheterodyne receiver wireless decoding

  [Transmitter module]  Product Model:  TX118SA-4 Transmitting power: 11dbm Distance: 25 meters above Emission current: 10MA Rate of fire: maximum 10KB / S Transmit deviation: +/- 7. 5KHZ / narrow-band emission Modulation: ASK Operating Voltage: DC 3V-24V Encoding:  Learning code EV1527  Each module has a unique ID address code. All modules K1-K4 four key code is the same.     Pin Description: - : Negative power supply +: Positive power supply, DC 3-24V   K1: 1 short to Negative start transmitting data, Similar the A button on the remote control. K2: 2 short to Negative start transmitting data, Similar the B button on the remote control. K3: 3 short to Negative start transmitting data, Similar...

Read more →


Qiachip | Product user manual | Catalog |

Instructions KR2201W KR2202 Latched Latching Momentary Receiver Module RF Toggle User manual Wi-Fi Ceiling Fan Remote Control Kit WIFI wifi ceiling fan controller

Qiachip  |  Product user manual  | Catalog |

New product preview! New products are coming online soon !!KR2201G a Small receiver ! Remote Control Switch User Manual 220V Remote Control Switch (Receiver) Qiachip KR2201-4 Wireless Remote Switch user manual Qiachip KR2201D Wireless Remote Switch user manual Qiachip KR2201G Wireless Remote Switch user manual Qiachip KR2201W Wireless Remote Switch user manual Qiachip KR2201WB Smart WIFI Remote Control user manual   Qiachip KR2202 Wireless Remote Switch user manual   12V Remote Control Switch (Receiver) Qiachip KR1201A 12V 1CH Wireless Remote Switch user manual Qiachip KR1202 12V 2CH Wireless Remote Switch user manual Qiachip KR1204 12V 4CH Wireless Remote Switch user manual   24V Remote Control Switch (Receiver)...

Read more →


How to use ? Qiachip KR2201W Wireless Remote Switch user manual

Instructions KR2201W Receiver Module RF User manual WIFI

How to use ? Qiachip KR2201W Wireless Remote Switch user manual

Safety Warning This device is for indoor use only. This device should not be exposed to dripping or splashing water or any danger Sources. This device should only be installed by adults. Do not install near any heat sources. Do not use this device with dimmers. Do not use this device in totally enclosed luminaires. Use this device in open luminaires only. If this device is much heavier than the one to be replaced , the increased weight may reduce the mechanical stability of certain luminaires and lampholders and may impair contact making and lamp retention. RISK OF ELECTRIC SHOCK:USE...

Read more →


RX500 RF Receiver Module user manual

Instructions Receiver Module RF RX500 User manual

RX500 RF Receiver Module user manual

Model: RX500 RX500 receiver module is receiving the UHF ASK demodulation equipment, support ASK demodulation. The receiver module has high sensitivity (-110dBm), low power consumption performance (<6mA), and a high dynamic range (greater than 60dB). The receiving module uses a highly integrated chip, built-in front-end low-noise amplifier, mixer, filter, frequency synthesizer and other circuits, which can optimize the signal to the greatest extent. Features RX500 receiver module has high sensitivity (-110dBm) and support ASK demodulation;Frequency: 315MHz(RX500-3) / 433.92MHz(RX500-4);Bandwidth 300KHz;Wide operating voltage range: 2.0V-5.0V;Low power consumption;Good selectivity and spurious radiation suppression, Can pass CE / FCC international certification easily;Good local oscillator...

Read more →


How to set the working mode of 2-channel remote switch receiver KR2202? Momentary; Toggle; Latching

Instructions KR2202 Latched Latching Momentary Toggle

How to set the working mode of 2-channel remote switch receiver KR2202? Momentary; Toggle; Latching

Function description and setting method of KR2202 (remote switch controller/receiver):

A) Reset function:
After pressing the learning button of the KR2202 8 times, the KR2202 clears all remote control data in its memory.
When the LED of the KR2202 flashes several times, the clear function is complete.
(When the data in KR2202 is cleared, all remote controllers (transmitters) cannot make KR2202 work)

 

Read more →